Hagmans - Filltec Light - Hagmans Nordic

Article number	Colour	Variant	Size	SDS	SDS 2
10942	Grey		1.11 KG	SDS	SDS 2
10982			1.11 KG	SDS	SDS 2
10983		Patron	1.75 L	SDS	SDS 2

2K lightweight polyester filler with very good sanding properties developed to fill dents and damage on body parts made of steel, galvanized steel, aluminum, and minor scratches in plastic. For professional use only.

Additional information

Product information

Product description

2K lightweight polyester putty with very good sanding properties developed for filling dents and damage on body parts made of steel, galvanized steel, aluminum, and minor scratches in plastic.
When used on galvanized surfaces, use a hardener that is no more than 12 months old. Some galvanized brands may require the surface to be cleaned with ammonia wash or alternatively sealed with 2K epoxy primer, so if in doubt, perform a test first.
For professional use only.
Area of application

Substrate:
Steel, galvanized steel, aluminum, polyester laminate, plastic (small and superficial scratches in hard/flexible plastics, max. 2 mm deep and 50 mm long), 2K Epoxy (max. layer thickness 15 μm)

Technical information

Application temperature

+15°C to +35°C.
Area of application

Steel, galvanized steel, aluminum, polyester laminate, plastic, 2K Epoxy
Base material

Unsaturated polyester
Cleaning

Hagmans Cellulose Thinner or thinner.
Colour

Component A is Light beige, Light Grey is Light grey, Hardener is red.
Density

0.85 kg/l
Drying time

Sanding possible after 15-20 minutes at 20°C. Sanding possible after 10 minutes with accelerated drying at 40°C. Sanding possible after 4 minutes. Use IR low intensity. The distance between the object and the IR lamp should be 50-70 cm. The object temperature must not exceed 70°C during drying.
Emballage

Comp. A (putty) is delivered in a jar. Comp. B (hardener) is delivered in a tube.
Fire class

2b
Flash-point

31°C
Härdartyp

50% benzoyl peroxide
Mixing ratio

Add 2-3% component B to component A and mix thoroughly
Potlife

Approx. 3-4 minutes with 2% hardener at +20°C
Re-paintable

With all non-water-dilutable primers
Shelf life

18 months
Storage

Store with a tightly closed lid. Best storage temperature +20°C (avoid large temperature variations)
VOC category

(Cat B/b) 250 g/l (2007).

Application

Mixing ratio

Mixing ratio:
100 parts Filltec Light Part A
2-3 parts Hardener
Pretreatment

Clean the surface before sanding.
Use warm soapy water, rinse with warm water.
Sand away any paint down to the bare metal surface with P180 – P240,
or scuff sand without going through any paint layer.
Before filling, clean and degrease the surface with a suitable
degreasing agent (Silicone remover).
Application

Apply the putty to the metal surface. Avoid thick putty edges around the damage; smooth the edges with the putty spatula.
Do not apply Filltec Light directly on old sanded paint surfaces or on acid-containing Washprimer.
For systems that are to meet the highest quality requirements regarding corrosion protection, Filltec Light should always be applied on 2K Epoxy primer (e.g., SprayMax 2K Epoxy primer).
After treatment

By hand: P120 – P180
Use control color.
With machine: P240 – P320. P400 for sanding during spot repair.
Check that there are no deep sanding scratches on the surface after sanding. Before spraying primer, filler, or surfacer, clean and degrease the substrate with a suitable degreasing agent. Avoid letting filled surfaces come into direct contact with water (e.g., water-based degreasing agents).